คำถามเกี่ยวกับ picostation2HP

วิธีการติดตั้ง และปรับแต่งอุปกรณ์ UBiQUiTi
ให้รองรับการทำงานที่หลากหลายความต้องการ

คำถามเกี่ยวกับ picostation2HP

โพสต์โดย vicifa403 เมื่อ พฤหัสฯ. 07 ก.ค. 2011 10:00 am

สามารถรองรับ client ได้ประมาณ กี่ user ครับ
แล้วช่อง poe ต่อเข้าตัว 2HP ส่วนช่อง Lan ตรง adapter ต่อเข้ากับ router ถูกต้องไหมครับ
ถ้าเพิ่มเสาอากาศ จะช่วยในเรื่องเพิ่มความเข้มข้นของสัญญาณ หรือ เพิ่มระยะทางครับ
vicifa403
 
โพสต์: 36
ลงทะเบียนเมื่อ: จันทร์ 06 มิ.ย. 2011 8:15 am

Re: คำถามเกี่ยวกับ picostation2HP

โพสต์โดย vicifa403 เมื่อ พฤหัสฯ. 07 ก.ค. 2011 10:53 am

Wireless mode :
1.station คือไรครับ
2.station WDS
3.Access Point
4.Access Point WDS
คืออะไรใช้ต่างกันยังไงครับผม
ขอบคุณมากครับ
vicifa403
 
โพสต์: 36
ลงทะเบียนเมื่อ: จันทร์ 06 มิ.ย. 2011 8:15 am

Re: คำถามเกี่ยวกับ picostation2HP

โพสต์โดย vicifa403 เมื่อ พฤหัสฯ. 07 ก.ค. 2011 10:54 am

network mode
1.Bridge
2.Router
คืออะไร ใช้ต่างกันยังไงครับ
กรณีทำเป็น access point ใช้ Bridge หรือ router ครับผม
ขอบคุณครับ
vicifa403
 
โพสต์: 36
ลงทะเบียนเมื่อ: จันทร์ 06 มิ.ย. 2011 8:15 am

Re: คำถามเกี่ยวกับ picostation2HP

โพสต์โดย sys2u เมื่อ พฤหัสฯ. 07 ก.ค. 2011 12:23 pm

vicifa403 เขียน:สามารถรองรับ client ได้ประมาณ กี่ user ครับ
แล้วช่อง poe ต่อเข้าตัว 2HP ส่วนช่อง Lan ตรง adapter ต่อเข้ากับ router ถูกต้องไหมครับ
ถ้าเพิ่มเสาอากาศ จะช่วยในเรื่องเพิ่มความเข้มข้นของสัญญาณ หรือ เพิ่มระยะทางครับ


  • สามารถรองรับ client ได้พร้อมกันไม่ต่ำกว่า 32+ ครับผม + วิธีการเชื่อมต่อของ PICO M2HP ตามที่เข้าใจเลยครับผม + ในกรณีที่เพิ่มเสาอากาศก็ต้องดูว่าเป็นเสาอากาศแบบไหนครับ ถ้าเพิ่มเป็น Indoor ก็จะได้เรื่องความเข้มของสัญญาณที่มากขึ้นแต่ไปได้ไม่ไกลครับ แต่ถ้าเป็น Outdoor ก็ต้องดูว่าเป็นเสาอากาศแบบไหนครับ ก็จะทำงานตามรูปแบบของการกระจายสัญญาณขอวเสาอากาศแต่ละประเภทครับ ลองดูรูปแบบของสัญญาณที่นี่นะครับ -> รูปแบบการกระจายสัญญาณไร้สายของเสาอากาศแบบ 3D

SYS2U.COM 24-Hour Online IT Store
ซิสทูยู เฟสบุ๊ค - http://www.facebook.com/SYS2UOnline

ภาพประจำตัวสมาชิก
sys2u
Administrator
 
โพสต์: 4716
ลงทะเบียนเมื่อ: อังคาร 30 ก.ย. 2008 12:35 pm
ที่อยู่: SYS2U.COM Bangkok, Thailand.

Re: คำถามเกี่ยวกับ picostation2HP

โพสต์โดย sys2u เมื่อ พฤหัสฯ. 07 ก.ค. 2011 12:31 pm

vicifa403 เขียน:Wireless mode :
1.station คือไรครับ
2.station WDS
3.Access Point
4.Access Point WDS
คืออะไรใช้ต่างกันยังไงครับผม
ขอบคุณมากครับ


    ตามนี้นะครับผม ข้อมูลเต็มที่นี่ครับ -> http://www.ubnt.com/wiki/AirOS_5

  1. Station: This is a client mode, which can connect to an AP.
    It is common for a bridging application to an AP. In Station mode device acts as the Subscriber Station while connecting to the Access Point which is primary defined by the SSID and forwarding all the traffic to/from the network devices connected to the Ethernet interface.
    The specifics of this mode is that Subscriber Station is using arpnat technique which may result lack of transparency while passing-through broadcast packets in bridge mode.

  2. Station WDS: WDS stands for Wireless Distribution System. Station WDS should be used while connecting to the Access Point which is operating in WDS mode. This mode is compatible with WPA/WPA2 encryption.
    Station WDS mode enables packet forwarding at layer 2 level.
    The benefit of Station WDS is improved performance and faster throughput. Station WDS - Bridge mode is fully transparent for all the Layer2 protocols.
    Refer to the section Network Settings for detailed Bridge network mode configuration information.

  3. Access Point: This is an 802.11 Access Point

  4. Access Point WDS: This is an 802.11 Access Point which allows for layer 2 bridging with Station WDS devices using the WDS protocol. AP WDS is not fully compatible with WPA/WPA2 encryption.
    WDS allows you to bridge wireless traffic between devices which are operating in Access Point mode. Access Point is usually connected to a wired network (Ethernet LAN) allowing wireless connection to the wired network. By connecting Access Points to one another in an Extended Service Set using the WDS, distant Ethernets can be bridged into a single LAN.

    It is very important that network loops should not be created with either WDS bridges or combinations of wired (Ethernet) connections and WDS bridges. Tree or Star shape network topology should be used in all WDS use-cases (i.e. if AP2 and AP3 are specified as the WDS peers of AP1, AP2 should not be specified as the WDS peer of AP3 and AP3 should not be specified as the WDS peer of AP2 in any case). Mesh and Ring network topologies are not supported by WDS and should be avoided in all the use cases.

    Note: Station WDS and AP WDS mode uses the WDS protocol which is not defined as the standard thus compatibility issues between equipment from different vendors may arise.
SYS2U.COM 24-Hour Online IT Store
ซิสทูยู เฟสบุ๊ค - http://www.facebook.com/SYS2UOnline

ภาพประจำตัวสมาชิก
sys2u
Administrator
 
โพสต์: 4716
ลงทะเบียนเมื่อ: อังคาร 30 ก.ย. 2008 12:35 pm
ที่อยู่: SYS2U.COM Bangkok, Thailand.

Re: คำถามเกี่ยวกับ picostation2HP

โพสต์โดย sys2u เมื่อ พฤหัสฯ. 07 ก.ค. 2011 12:35 pm

vicifa403 เขียน:network mode
1.Bridge
2.Router
คืออะไร ใช้ต่างกันยังไงครับ
กรณีทำเป็น access point ใช้ Bridge หรือ router ครับผม
ขอบคุณครับ



    ตามนี้นะครับผม ข้อมูลเต็มที่นี่ครับ -> http://www.ubnt.com/wiki/AirOS_5

  1. [Bridge] operating mode is selected by default as it is widely used by the subscriber stations, while connecting to Access Point or using WDS. In this mode the device will act as a transparent bridge and will operate in Layer 2. There will be no network segmentation while broadcast domain will be the same. Bridge mode will not block any broadcast or multicast traffic. Additional Firewall settings can be configured for Layer 2 packet filtering and access control in Bridge mode.


    In bridge mode the AirOS v5.0 based device forwards all the network management and data packets from one network interface to the other without any intelligent routing. For simple applications this provides efficient and fully transparent network solution. WLAN (wireless) and LAN (Ethernet) interfaces belong to the same network segment which has the same IP address space. WLAN and LAN interfaces form the virtual bridge interface while acting as the bridge ports. The bridge has assigned IP settings for management purposes:



  2. [Router] operating mode can be configured in order to operate in Layer 3 to perform routing and enable network segmentation – wireless clients will be on different IP subnet. Router mode will block broadcasts while it is not transparent.
    AirOS v5.0 supports Multicast packet pass-through in Router mode.
    AirOS v5.0 powered Router can act as DHCP server and use Network Address Translation (Masquerading) feature which is widely used by the Access Points. NAT will act as the firewall between LAN and WLAN networks. Additional Firewall settings can be configured for Layer 3 packet filtering and access control in Router mode.


    The role of the LAN and WLAN interface will change accordingly to the Wireless Mode while the AirOS powered device is operating in Router mode:

    • Wireless interface and all the wireless clients connected are considered as the internal LAN and the Ethernet interface is dedicated for the connection to the external network while the AirOS powered device is operating in AP/AP WDS wireless mode;
    • Wireless interface and all the wireless clients connected is considered as the external network and the all the network devices on LAN side as well as the Ethernet interface itself is considered as the internal network while the AirOS powered device is operating in Station/Station WDS mode.
    Wireless/wired clients are routed from the internal network to the external one by default. Network Address Translation (NAT) functionality works the same way.
SYS2U.COM 24-Hour Online IT Store
ซิสทูยู เฟสบุ๊ค - http://www.facebook.com/SYS2UOnline

ภาพประจำตัวสมาชิก
sys2u
Administrator
 
โพสต์: 4716
ลงทะเบียนเมื่อ: อังคาร 30 ก.ย. 2008 12:35 pm
ที่อยู่: SYS2U.COM Bangkok, Thailand.


ย้อนกลับไปยัง วิธีการติดตั้งและปรับแต่งอุปกรณ์ UBiQUiTi (ยูบิ-ควิ-ตี้)

ผู้ใช้งานขณะนี้

กำลังดูบอร์ดนี้: ไม่มีสมาชิกใหม่ และ บุคคลทั่วไป 13 ท่าน

cron