มาตรฐาน IEEE 802.11n-2009, MIMO และ 40 MHz

ข้อมูลทั่วไป ระบบคอมพิวเตอร์เบื้องต้น ระบบเครือข่ายเบื้องต้น
สำหรับผู้เริ่มต้นในการทำความเข้าใจระบบคอมพิวเตอร์ ระบบเครือข่ายแบบสาย และไร้สาย

มาตรฐาน IEEE 802.11n-2009, MIMO และ 40 MHz

โพสต์โดย sys2u เมื่อ พุธ 14 เม.ย. 2010 1:43 pm

รูปภาพ มาตรฐาน IEEE 802.11n-2009, MIMO และ 40 MHz - Wikipedia
บทความสำหรับ: ผู้ที่มีความรู้เกี่ยวกับระบบเครือข่ายในระดับเบื้องต้นถึงปานกลาง รูปภาพ
โดย ศุภสิทธิ์ ศิริพานิชกร


ท่านสามารถดาวน์โหลดบทความ IEEE 802.11n-2009 ได้ที่ http://en.wikipedia.org/wiki/IEEE_802.11n-2009
ท่านสามารถดาวน์โหลดบทความ MIMO ได้ที่ http://en.wikipedia.org/wiki/Multiple-i ... ple-output


Description
IEEE 802.11n is an amendment to IEEE 802.11-2007 as amended by IEEE 802.11k-2008, IEEE 802.11r-2008, IEEE 802.11y-2008, and IEEE 802.11w-2009, and builds on previous 802.11 standards by adding multiple-input multiple-output (MIMO) and 40 MHz channels to the PHY (physical layer), and frame aggregation to the MAC layer.

    MISO A system which uses multiple antennas at the transmitter and a single antenna at the receiver is named Multiple Input Single Output (MISO). A technique known as Alamouti STC (Space Time Coding) is employed at the transmitter with two antennas. STC allows the transmitter to transmit signals (information) both in time and space, meaning the information is transmitted by two antennas at two different times consecutively.

    Multiple antennas (each with an RF chain) of either SIMO or MISO are usually placed at a base station (BS). This way, the cost of providing either a receive diversity (in SIMO) or transmit diversity (in MISO) can be shared by all subscriber stations (SSs) served by the BS.

    MISO.gif
    MISO.gif (2.27 KiB) เปิดดู 4730 ครั้ง

    Figure. Multiple Input Single Output (MISO), 2x1
    Two antennas at the transmitter, one antenna at the receiver.
    Employs a transmit diversity technique.



    MIMO is a technology which uses multiple antennas to coherently resolve more information than possible using a single antenna. One way it provides this is through Spatial Division Multiplexing (SDM). SDM spatially multiplexes multiple independent data streams, transferred simultaneously within one spectral channel of bandwidth. MIMO SDM can significantly increase data throughput as the number of resolved spatial data streams is increased. Each spatial stream requires a discrete antenna at both the transmitter and the receiver. In addition, MIMO technology requires a separate radio frequency chain and analog-to-digital converter for each MIMO antenna which translates to higher implementation costs compared to non-MIMO systems.

    To multiply throughput of a radio link, multiple antennas (and multiple RF chains accordingly) are put at both the transmitter and the receiver. This system is referred to as Multiple Input Multiple Output (MIMO). A MIMO system with similar count of antennas at both the transmitter and the receiver in a point-to-point (PTP) link is able to multiply the system throughput linearly with every additional antenna. For example, a 2x2 MIMO will double the throughput.

    MIMO.gif
    MIMO.gif (2.44 KiB) เปิดดู 4744 ครั้ง

    Figure. Multiple Input Multiple Output (MIMO), 2x2
    Two antennas at both the transmitter and the receiver.



    40 MHz channels is another feature incorporated into 802.11n which doubles the channel width from 20 MHz in previous 802.11 PHYs to transmit data. This allows for a doubling of the PHY data rate over a single 20 MHz channel. It can be enabled in the 5 GHz mode, or within the 2.4 GHz if there is knowledge that it will not interfere with any other 802.11 or non-802.11 (such as Bluetooth) system using those same frequencies.
    Coupling MIMO architecture with wider bandwidth channels offers increased physical transfer rate over 802.11a (5 GHz) and 802.11g (2.4 GHz).






Data rates
Data rates up to 600 Mbit/s are achieved only with the maximum of four spatial streams using a 40 MHz-wide channel. Various modulation schemes and coding rates are defined by the standard and are represented by a Modulation and Coding Scheme (MCS) index value. The table below shows the relationships between the variables that allow for the maximum data rate.

    รูปภาพ



    ตารางเปรียบเทียบ

    รูปภาพ



SYS2U.COM 24-Hour Online IT Store
ซิสทูยู เฟสบุ๊ค - http://www.facebook.com/SYS2UOnline

ภาพประจำตัวสมาชิก
sys2u
Administrator
 
โพสต์: 4716
ลงทะเบียนเมื่อ: อังคาร 30 ก.ย. 2008 12:35 pm
ที่อยู่: SYS2U.COM Bangkok, Thailand.

ย้อนกลับไปยัง ข้อมูลทั่วไป ระบบคอมพิวเตอร์เบื้องต้น ระบบเครือข่ายเบื้องต้น

ผู้ใช้งานขณะนี้

กำลังดูบอร์ดนี้: ไม่มีสมาชิกใหม่ และ บุคคลทั่วไป 11 ท่าน

cron